• Registered: 2017-10-16
  • Posts: 7

Topic: Prima installazione :-)

A Greeting to All the Forum, i write from Italy.

[[[ sorry for writing errors, I'm using Google Translate ... ]]]

I am a happy owner of a Golf 5 TDI 1.9, running on the web I came across your product marketed by: https://www.turbozentrum.de/
ordered and shipped very fast, I installed it to the Gateway as in the manual found on the site, and I enabled the Telematics command with Vag-Com 12.12.
the menu of my MFA + has added the FIS-CONTROL menu.
The first thing I did was updating the Firmware (Version 2017-10-15) I found on the site, with the Android app wink
Unfortunately I did not understand how to use the configurator that generates the file.dat to show all the parameters on my MFA + I tried to put the same parameters as I saw in the video on YouTube and uploaded them to Android App but nothing changed hmm
Now I humbly ask if anyone has a "Fis_Control.dat" file for Golf 5 TDI 1.9 to download and then load it into the Configurator to see how all the entries are set up so I can understand in the future how I have to put the parameters in the Configurator smile
Unfortunately this is the first time I venture into such a thing for my knowledge, and I would like to learn tongue
I hope you can help me, and I still apologize for the bad writing using Google Translate from ITALY.

  • From: Hessen / Germany
  • Registered: 2015-01-01
  • Posts: 2,070

Re: Prima installazione :-)

Hi,

could you please attach your configuration file. I will have a look at it.

stefan@fis-control's Website

  • Registered: 2017-10-16
  • Posts: 7

Re: Prima installazione :-)

Good morning and thank you for having responded, I attach the file with the few parameters I entered. basically resembles the settings I've seen on YouTube video ...

I attach the file I generated with the Configurator

Post's attachments

fis_control_Golf_5.dat 64 kb, 2 downloads since 2017-10-17 

You don't have the permssions to download the attachments of this post.
  • From: Hessen / Germany
  • Registered: 2015-01-01
  • Posts: 2,070

Re: Prima installazione :-)

Ah, the main problem in your configuration is that you have not enabled the CAN bus.
The FIS-Control has to read all measurements in the Golf 5 via CAN bus, so please enable the "CAN" check box for every measurement value.
Plase also go to the section "Control unit settings" and select the instrument cluster, enable the "CAN" and set the block delay to 85.

stefan@fis-control's Website

5 Reply by tortorellibiagio (edited by tortorellibiagio 2017-10-18 15:55:48)

  • Registered: 2017-10-16
  • Posts: 7

Re: Prima installazione :-)

Good morning, I set up all the CAN protocols and saved the file.dat I transferred with the android app to Fis-Control
but unfortunately gave me connection error as in attached photos,

http://i68.tinypic.com/2cyfkh3.jpg

===

http://i66.tinypic.com/2v3t01t.jpg

===

http://i65.tinypic.com/2eb7b85.jpg

turning to the forum I read a post to select ENGINE entry in FIS settings, and select the engine with the asterisk ... ( * )
and I did try to set the FIS with the engine parameter with the asterisk ... as with attached pictures

http://i65.tinypic.com/2my9tdt.jpg

===

http://i67.tinypic.com/15ozbtf.jpg

===

http://i64.tinypic.com/339kk0k.jpg

save the settings, I went to preset 1 to see if it works,

http://i64.tinypic.com/16htbp5.jpg

big_smile big_smile big_smile big_smile

finally something can move

then I noticed a strange thing in the configurator, when I load the previously saved PC file, I change some settings, onon saves the previous setting as well as from the photo ...

http://i68.tinypic.com/34dsndj.jpg

you have to set the control unit again

http://i66.tinypic.com/sdfnlc.jpg

and re-flag the CAN protocol

http://i67.tinypic.com/wsny2v.jpg

and save the file on my PC, but if I reload it in the configurator i disappear from the settings mentioned above ....

Now I'm trying to set preset 2 for the TURBO BOOST screen, I tried various parameters but I can not set it either from where FIS-CONTROL has to draw the parameters to climb the scale in the instrument panel

http://i65.tinypic.com/29p6ng3.jpg

it is obviously wrong to insert the TURBO sensor assembly because I see RPM as a value and the fingers do not move

then I saw in the CONFIGURATOR you can not select CONTROL UNIT 01* ENGINE as well as from photo

http://i64.tinypic.com/339kk0k.jpg

but ends up with the setting: 7F

http://i64.tinypic.com/2sba61j.jpg

practically ENGINE with the asterisk ( * ) alone on the Fis-Control

  • From: Hessen / Germany
  • Registered: 2015-01-01
  • Posts: 2,070

Re: Prima installazione :-)

Hi, I have to admit that this is a little confusing.
In the FIS-Control menus the asterisk (*) indicates that for the selected control module the CAN bus should be used.
In the configurator you do the same thing when selecting the "CAN" checkbox.

So when you do the configuration of the presets or the control units:
1. Select the control unit you want
2. Select if it is accessed via K line or CAN bus
3. Then do the rest of the configuration

stefan@fis-control's Website

  • From: Hessen / Germany
  • Registered: 2015-01-01
  • Posts: 2,070

Re: Prima installazione :-)

To show the correct turbo boost pressure, you have to tell the FIS-Control, where to find that value ("CONTROL UNIT", "GROUP", "VALUE"). For gasoline cars, this is normally the fourth value of the group 115 of the engine control unit.

Set the "UPPER LIMIT"  to match the highest expected pressure. The values are always in the unit in which they are displayed. If you expect a boost pressure of up to 2500 mbar, set the "UPPER LIMIT" to "+002500.000" (the point is a decimal point). If the boost pressure is shown in Bar instead, enter "+000002.500".

Additionally you should configure the boost display at "SETTINGS" -> "BOOST" to show the unit "BAR" or "PSI" and the "GAUGE" scale.

stefan@fis-control's Website

8 Reply by tortorellibiagio (edited by tortorellibiagio 2017-10-19 14:24:31)

  • Registered: 2017-10-16
  • Posts: 7

Re: Prima installazione :-)

Yessssssss

https://youtu.be/ZH-nTsvG9vU

  • From: Hessen / Germany
  • Registered: 2015-01-01
  • Posts: 2,070

Re: Prima installazione :-)

Very cool.

stefan@fis-control's Website