Topic: Hi, help me please !!
How to obtain accurate turbine dat,
A4 b7
You are not logged in. Please login or register.
FIS-Control Forum → English forum → Hi, help me please !!
How to obtain accurate turbine dat,
A4 b7
If you have a gasoline engine, you can find the boost pressure in group 115, value 4 in your engine control unit.
If you have a gasoline engine, you can find the boost pressure in group 115, value 4 in your engine control unit.
Hello, I have already made the settings as requested, but it is still the same.
Just to be sure. Do you have diesel or gasoline engine?
Just to be sure. Do you have diesel or gasoline engine?
A4 B7 2.0T (manual) gasoline engine.
Ok, then it should actually work.
Please double checke the following settings for your preset:
Control unit: 01 ENGINE (or maybe "01* ENGINE", if needed)
Group: 115
Value 4
And also in at SETTINGS -> BOOST:
Control unit: 01
Group: 115
Unit: Bar
Scale: Gauge
Ok, then it should actually work.
Please double checke the following settings for your preset:
Control unit: 01 ENGINE (or maybe "01* ENGINE", if needed)
Group: 115
Value 4And also in at SETTINGS -> BOOST:
Control unit: 01
Group: 115
Unit: Bar
Scale: Gauge
When I select 01 ENGINE it becomes OBD error
Then select "01* ENGINE". And also set:
SETTINGS -> TWEAKS -> OBD TIMING
to
CONTROL UNIT: 01* ENGINE
BLOCK DELAY: 085
Then select "01* ENGINE". And also set:
SETTINGS -> TWEAKS -> OBD TIMING
to
CONTROL UNIT: 01* ENGINE
BLOCK DELAY: 085
The result is the same. I don't know which step went wrong.
Could you please go to the FIS-Control main menu and start a MEASUREMENT.
Is it able to show measurement values of the engine control unit?
If yes, go to measurement block 115 and check if the boost is shown there.
Could you please go to the FIS-Control main menu and start a MEASUREMENT.
Is it able to show measurement values of the engine control unit?
If yes, go to measurement block 115 and check if the boost is shown there.
Like this…….
Yes, but you have to select the "ENGINE" as the current control unit. You can do it at SETTINGS -> CONTROL UNIT.
Yes, but you have to select the "ENGINE" as the current control unit. You can do it at SETTINGS -> CONTROL UNIT.
Hello,I regret to inform you that the outcome remains the same.
So you tried "01 ENGINE" and also "01* ENGINE"?
Maybe your engine control module uses the UDS protocol.
Do you have VCDS? There you can check the used protocol.
So you tried "01 ENGINE" and also "01* ENGINE"?
Maybe your engine control module uses the UDS protocol.
Do you have VCDS? There you can check the used protocol.
Yep, my VCDS is channel 62 to the value "5"
Could you please connect VCDS to your engine control unit? In the upper left corner of VCDS, you will then see a info box with the diagnostic protocol. It is either "CAN" or "UDS".
Could you please connect VCDS to your engine control unit? In the upper left corner of VCDS, you will then see a info box with the diagnostic protocol. It is either "CAN" or "UDS".
''CAN''
Perfect. Then it should work with the following settings:
In the Preset:
Control unit: 01* ENGINE
Group: 115
Value 4
And in SETTINGS -> BOOST:
Control unit: 01* ENGINE
Group: 115
Unit: Bar
Scale: Gauge
And in SETTINGS -> TWEAKS -> OBD TIMING
Control unit: 01* ENGINE
Block Delay: 085
Perfect. Then it should work with the following settings:
In the Preset:
Control unit: 01* ENGINE
Group: 115
Value 4And in SETTINGS -> BOOST:
Control unit: 01* ENGINE
Group: 115
Unit: Bar
Scale: GaugeAnd in SETTINGS -> TWEAKS -> OBD TIMING
Control unit: 01* ENGINE
Block Delay: 085
“Yes, that’s how I set it up, but the results are still the same. Could it be a problem with the installation of my control box?”
Yes, please check the wiring.
Like this⋯⋯
Wiring looks correct.
Could you also send photos of your settings in the FIS-Control? Or write what exactly is configured for your preset.
Wiring looks correct.
Could you also send photos of your settings in the FIS-Control? Or write what exactly is configured for your preset.
My settings are configured as you suggested, but initially, I had a red monochrome screen. Now, I've changed it to a color screen.
Additionally, sometimes there are ghosting issues with the fonts, leaving a faint afterimage on the screen.
In the Preset:
Control unit: 01* ENGINE
Group: 115
Value 4
And in SETTINGS -> BOOST:
Control unit: 01* ENGINE
Group: 115
Unit: Bar
Scale: Gauge
And in SETTINGS -> TWEAKS -> OBD TIMING
Control unit: 01* ENGINE
Block Delay: 085
The ghosting issues can be solved when you select "ALT BAR GRAPHS" at SETTINGS -> TWEAKS.
Do you have VCDS, ot any other diagnostic tool? Could you check that you can read the boost pressure with that tool?
The ghosting issues can be solved when you select "ALT BAR GRAPHS" at SETTINGS -> TWEAKS.
Do you have VCDS, ot any other diagnostic tool? Could you check that you can read the boost pressure with that tool?
Yep! I have VCDS & OBDeleven
FIS-Control Forum → English forum → Hi, help me please !!
Powered by PunBB, supported by Informer Technologies, Inc.