• Registered: 2021-06-25
  • Posts: 6

Topic: Audi S1 FIS-Control not working

Hello!

I just installed the FIS-Control module in my Audi S1. I have te MMI 3G+.

I followed this persons instructions: https://www.a1talk.de/threads/fis-contr … -s1.11379/ .

After installing the Fis module, I started my car up and everything works like before. My buttons operate, my radio works... But I don't get the Fis screen. It seemes like nothing has changed... Do i have to do something to get to the Fis screen to show? Or are the instruction of the German guy not correct?

(When I started the car, the only thing I did was turn the key)

  • From: Hessen / Germany
  • Registered: 2015-01-01
  • Posts: 2,070

Re: Audi S1 FIS-Control not working

Hi, I changed the behaviour a little bit. The FIS-Control will not show anything on the screen unless it received a configuration file, so that it knows in which car model it is installed.

You should prepare a valid config file with the configurator: https://fis-control.de/mmi.html

If you turn on the ignition, the FIS-Control should be found via Bluetooth for a minute (after a minute without a connection, the Bluetooth module of the FIS-Control will turn off).
Now connect the Android app to your FIS-Control and upload at least the current firmware and your new config file. Both can be done with the "MMI: Fast upload" option in the app. Please wait about 30 seconds after you transferred the new firmware before you restart the ignition.

stefan@fis-control's Website

3 Reply by diedes (edited by diedes 2021-06-25 14:37:57)

  • Registered: 2021-06-25
  • Posts: 6

Re: Audi S1 FIS-Control not working

Hello,

thanks for your response. I tried do to everything you said and i managed to get the gauges on my screen. However the gauges are empty. They have no value and no needles. I think i used the wrong ECU datasheet. So i read my ecu with the android app. I don't know what datasheet i should be using.


(I was able to read the battery voltage on the second screen)


Result:

FIS-CONTROL
SW: 2021-06-20
Serial: 00430044 41525009 20393654

Reading all values...
ECU index: 0000
1B 62 F1 9E 45 56 5F 45 43 4D 32 30 54 46 53 30 32 30 38 58 30 39 30 36 32 35 39 00
09 62 F1 A2 30 30 31 30 30 36
221112121112#21122##122121111422###212222111#4411#111222222222222222212#1
#111######################################################TTT
TTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTT211122211##a###1211#221###21222211#
#2221###2##1#192211##22#2###############22##

Post's attachments

205502890_355344246151275_5751697004788567066_n.jpg 27.56 kb, file has never been downloaded. 

You don't have the permssions to download the attachments of this post.
  • From: Hessen / Germany
  • Registered: 2015-01-01
  • Posts: 2,070

Re: Audi S1 FIS-Control not working

Hi, your ECU uses dataset "EV_ECM20TFS0208X0906259_001006".

stefan@fis-control's Website

5 Reply by diedes (edited by diedes 2021-07-06 17:57:45)

  • Registered: 2021-06-25
  • Posts: 6

Re: Audi S1 FIS-Control not working

Thank you very much!!

The 3 gauges work perfectlt, but now the problem is that i wanted to configure the 2nd table. I think I did everything correctly, i used the same ECU dataset. All the information that i manually put in I can see, but the actual values don't appear?

Post's attachments

Datasheet audi.png 298.38 kb, file has never been downloaded. 

You don't have the permssions to download the attachments of this post.
  • From: Hessen / Germany
  • Registered: 2015-01-01
  • Posts: 2,070

Re: Audi S1 FIS-Control not working

Hi, this is a common problem. Many control units do not allow to read more than 8 parameters at once.
Keep two entries of the table <empty> and it will work.

stefan@fis-control's Website

  • Registered: 2021-06-25
  • Posts: 6

Re: Audi S1 FIS-Control not working

Yes! Thank you! Everything works perfectly!