Hi, for the temperature you can pick the "0261230340 TE" from the sensor list of the FIS-Control. It does exactly match your sensor.
376 2022-07-13 19:13:01
Re: Oil pressure sensor Bosh Motorsport PST-F 1 (18 replies, posted in English forum)
377 2022-07-12 22:33:47
Re: Oil pressure sensor Bosh Motorsport PST-F 1 (18 replies, posted in English forum)
Hi, the pressure signal of the Bosch sensor seems to be identical to the Zadatech oil pressure sensor.
I will check tomorrow about the temperature. If it is not available in the FIS-Control yet, I will add it.
The wire gauge does not really matter for these sensor signals as almost no current is flowing.
378 2022-07-10 14:01:44
Re: Hilfe beim RS3 8p (25 replies, posted in Probleme / Wünsche / Verbesserungsvorschläge)
Ich hänge dir nochmal eine Minimal-Konfiguration an. Die sollte auf jeden Fall laufen.
Hinweis: Nach dem Hochladen nicht (!) auf EINSTELLUNGEN -> SPEICHERN gehen. Sonst wird die neue Datei gleich wieder mit den bisher aktiven Einstellungen überschrieben.
Also einfach nach dem Hochladen die Zündung aus und wieder einschalten.
379 2022-07-10 13:55:51
Re: Hilfe beim RS3 8p (25 replies, posted in Probleme / Wünsche / Verbesserungsvorschläge)
Hm, das sollte eigentlich gehen. Sicher dass der zweipolige Stecker mit rotem Schmpfschlauch in Buchse F vom FIS-Control richtig steckt?
Hast du parallel irgendein anderes Diagnosetool laufen, z.B. OBDeleven?
380 2022-07-10 13:49:07
Re: Hilfe beim RS3 8p (25 replies, posted in Probleme / Wünsche / Verbesserungsvorschläge)
Sieht eigentlich ok aus. Geh mal im FIS-Control auf EINSTELLUNGEN -> STEUERGERÄT. Was steht da?
381 2022-07-10 13:05:31
Re: Hilfe beim RS3 8p (25 replies, posted in Probleme / Wünsche / Verbesserungsvorschläge)
Aber kommen die CCCC schon direkt, wenn du dich mit dem Terminalprogramm verbindest? Dann wirst du nochmal die Firmware senden müssen.
382 2022-07-10 12:40:58
Re: Hilfe beim RS3 8p (25 replies, posted in Probleme / Wünsche / Verbesserungsvorschläge)
Wenn das FIS-Control schon direkt CCCC sendet, bevor du ein Kommando eingetippt hast, dann ist das FIS-Control im Softwarelade-Modus und du musst erst eine Firmware-Datei an das FIS-Control senden bevor du etwas anderes machen kannst.
383 2022-07-10 11:26:01
Re: Hilfe beim RS3 8p (25 replies, posted in Probleme / Wünsche / Verbesserungsvorschläge)
Wenn du hier im Forum statt im "Quick reply to this topic" Feld erst auf "Post reply" klickst, kannst du Dateien und Bilder anhängen.
384 2022-07-09 22:45:29
Re: Hilfe beim RS3 8p (25 replies, posted in Probleme / Wünsche / Verbesserungsvorschläge)
Ah ok. Du willst also eine neue Konfig-Datei an das FIS-Control senden, richtig?
Wenn du das vom PC aus machen willst, musst du erst SEND SETTINGS in das Terminal eintippen und dann Enter drücken.
Es ist dabei übrigens normal, dass man die Buchstaben beim Eintippen nicht sieht, es sei denn man aktiviert die Echo-Funktion im Terminal.
Wenn der SEND SETTINGS-Befehl geklappt hat, dann sollte das FIS-Control jetzt einmal pro Sekunde den Buchstaben C an das Terminal schicken. Erst dann kannst du die Datei übertragen.
385 2022-07-09 22:35:11
Re: Hilfe beim RS3 8p (25 replies, posted in Probleme / Wünsche / Verbesserungsvorschläge)
Tach,
beom Kommunikationsproblem mit dem Steuergerät tippe ich darauf, dass im FIS-Control das Steuergerät "ohne Sternchen" ausgewählt wurde. Jedes Steuergerät ist nämlich zweimal in den Auswahllisten. Einmal mit und einmal ohne Sternchen. Beim läuft die Diagnose immer über CAN-Bus. Daher immer das Steuergerät mit Sternchen auswählen.
Siehe auch:
https://fis-control.de/handbuch.html#c73
Bezüglich Bluetooth. Klappt das auch dann nicht, wenn du während des Einschaltens der Zündung die Runtertaste seitlich am Wischerhebel gedrückt hältst?
386 2022-07-04 21:55:06
Re: Help Collection Setting (30 replies, posted in English forum)
Yes, it should be possible when you set SETTINGS -> HEADLINE -> RADIO.
387 2022-07-04 21:38:46
Re: Help Collection Setting (30 replies, posted in English forum)
Yes, you can change the label of a preset. I think I just left the label field for Preset 1 empty, so it will default to "PRESET 1". but you can enter a different name there.
Boost should be zero of Engine is off.
388 2022-07-04 16:10:20
Re: Help Collection Setting (30 replies, posted in English forum)
I assume that you have selected "SAVE SETTINGS" after you uploaded the config file.
Do not do this, because this will overwrite the settings file with the currently active settings.
Just restart the ignition instead.
So:
Go to SETTINGS -> FLASH MEMORY -> LOAD SETTINGS -> BLUETOOTH
Then transfer the settings file.
When done, just restart the ignition.
389 2022-07-02 22:38:08
Re: Ob ich wohl zu dumm bin ... ??? (7 replies, posted in Allgemeine Diskussion)
Hi, super dass es geklappt hat.
Dieses Codieren vom Gateway ist nicht gerade intuitiv.
390 2022-07-02 21:48:27
Re: Help Collection Setting (30 replies, posted in English forum)
Hi, please try the attached settings file.
391 2022-07-02 21:38:10
Re: Accessing ABS controller (2 replies, posted in English forum)
Normallly the FIS-Control should be able to communicate with the ABS controller.
Was your car standing still while you tried to connect? ABS controller does not accept new connections while the car is moving.
392 2022-07-02 19:20:06
Re: Ob ich wohl zu dumm bin ... ??? (7 replies, posted in Allgemeine Diskussion)
Bei den älteren Sharans (vor 2001) gab es noch kein CAN-Gateway, das codiert werden muss. Ab 2001 gibt es das CAN-Gateway.
Du kannst daher mal folgendes probieren:
-----------
Bei VW wird die Verbauliste automatisch aktualisiert, wenn man das CAN-Gateway (Steuergerät 19) mit dem bereits kodierten Softcoding neu kodiert.
-----------
393 2022-07-02 11:09:14
Re: Help Collection Setting (30 replies, posted in English forum)
No, the collections are not ok.
If you tell me, which measurements you want to have in your collections, I could create a config file for you.
394 2022-06-27 16:20:27
Re: Help Collection Setting (30 replies, posted in English forum)
Did you select SETTINGS -> FLASH MEMORY -> LOAD SETTINGS -> RS-232 in the FIS-Control?
You should see the letter C every second in the Terminal program on your laptop then.
395 2022-06-26 20:32:29
Re: Help Collection Setting (30 replies, posted in English forum)
Did you set the baudrate correctly? For USB cable it is necessary to set it to 115200 bit/s.
396 2022-06-24 18:35:43
Re: Ladedruck anpassen nicht möglich im B5 (4 replies, posted in Probleme / Wünsche / Verbesserungsvorschläge)
Dann ist das Motorsteuergerät unter EINSTELLUNGEN -> MASKIERUNG ausgeblendet.
Hier im Handbuch ist beschrieben, wie man das einstellt:
https://fis-control.de/handbuch.html#c52
397 2022-06-24 15:32:14
Re: Ladedruck anpassen nicht möglich im B5 (4 replies, posted in Probleme / Wünsche / Verbesserungsvorschläge)
Prüfe bitte, ob unter EINSTELLUNGEN -> LADEDRUCK -> STEUERGERÄT auch wirklich "01 MOTOR" steht. Falls da "01* MOTOR" steht (also mit Sternchen), dann hast du in der Liste den falschen Eintrag erwischt.
Und ist unter EINSTELLUNGEN -> LADEDRUCK -> BLOCK auch tatsächlich der richtige Messwertblock (also z.B. 115) eingestellt?
398 2022-06-17 16:29:18
Re: Problem bei Audi A3 mit Alpine-Navi gelöst (3 replies, posted in Probleme / Wünsche / Verbesserungsvorschläge)
Nein, Stromversorgung muss nicht vom Gateway kommen.
399 2022-06-17 10:47:37
Re: Problem bei Audi A3 mit Alpine-Navi gelöst (3 replies, posted in Probleme / Wünsche / Verbesserungsvorschläge)
Hi, danke für die Infos.
400 2022-06-14 13:19:37
Re: Kein Bild im MMI 3G (5 replies, posted in Probleme / Wünsche / Verbesserungsvorschläge)
Wie viele Messwerte hast du in die Tabelle reingepackt? Etliche Steuergeräte können nur 8 Messwerte gleichzeitig ausgeben, nicht 10.
In diesem Fall musst du die Anzahl pro Tabellenseite einfach reduzieren.
Was jetzt genau dein Problem mit der Hintergrundgrafik ist, weiß ich nicht. Du kannst mir deine Dateien per eMail schicken, dann schaue ich mal drüber.